OVH Community, your new community space.

rescue mode test results


Myatu
12-07-2009, 14:49
Ah, I had some fun with this last month...

Quote Originally Posted by handout
Could some of you guys see if there is any problem with this test result for the harddrive.
...
5 Reallocated_Sector_Ct 0x0033 096 096 036 Pre-fail Always - 199
This bit means that 199 sectors have been marked as bad, and the HD is using spare sectors for them instead.

Quote Originally Posted by handout
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1
And this shows that it currently has one more sector the HD has trouble reading from. If it can read from it at a later time, or data can successfully be written to it, then this will disappear. On the other hand, if it cannot do any of this with success, then it will also be marked bad and replaced.

Quote Originally Posted by handout
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 5
...
Error 1287 occurred at disk power-on lifetime: 4800 hours (200 days + 0 hours)
This is the error I had to deal with on my 2nd HD last month and will certainly cause read/write errors. In my case, the RAID1 setup went into a sort of limp mode by suspending the 2nd HD as it discovered inconsistencies during a resync. Such is the usefulness of RAID1: keeps your server up and running.

I could correct the issue (requiring a full format of the physical HD), but then I did not have 199 sectors marked as bad -- this is something of a worry IMHO.

I would raise a support ticket through OVH's Manager with the information you've just provided (we, and by that I mean OVH customers, can only share our knowledge and not assist with support). Or, wait until tomorrow morning and give them a call.

P.S.: It seems you're using a Kimsufi server. The Kimsufi forum is located at http://forum.kimsufi.co.uk/ - this would mean you don't have RAID setup.
handout
12-07-2009, 12:42
Could some of you guys see if there is any problem with this test result for the harddrive.
Been getting some read/write errors so i ran the tests in rescue mode and the only errors were on the harddrive

smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model: ST3250410AS
Serial Number: 6RYDR4JB
Firmware Version: 4.AAA
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Jul 12 11:45:33 2009 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 64) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 253 006 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 145
5 Reallocated_Sector_Ct 0x0033 096 096 036 Pre-fail Always - 199
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 158715693
9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 4801
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 148
187 Unknown_Attribute 0x0032 001 001 000 Old_age Always - 1281
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Unknown_Attribute 0x0022 061 047 045 Old_age Always - 890568743
194 Temperature_Celsius 0x0022 039 053 000 Old_age Always - 39 (Lifetime Min/Max 0/21)
195 Hardware_ECC_Recovered 0x001a 058 048 000 Old_age Always - 197475508
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 5
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 1288 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1288 occurred at disk power-on lifetime: 4800 hours (200 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f2 7a 59 e5 Error: UNC at LBA = 0x05597af2 = 89750258

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 eb 7a 59 e5 00 02:24:57.798 READ DMA
27 00 00 00 00 00 e0 00 02:24:57.797 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 02:24:57.783 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 02:24:57.782 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 02:24:57.775 READ NATIVE MAX ADDRESS EXT

Error 1287 occurred at disk power-on lifetime: 4800 hours (200 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f2 7a 59 e5 Error: UNC at LBA = 0x05597af2 = 89750258

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 eb 7a 59 e5 00 02:24:49.737 READ DMA
27 00 00 00 00 00 e0 00 02:24:49.732 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 02:24:45.590 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 02:24:45.590 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 02:24:45.589 READ NATIVE MAX ADDRESS EXT

Error 1286 occurred at disk power-on lifetime: 4800 hours (200 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f2 7a 59 e5 Error: UNC at LBA = 0x05597af2 = 89750258

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 eb 7a 59 e5 00 02:24:49.737 READ DMA
27 00 00 00 00 00 e0 00 02:24:49.732 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 02:24:45.590 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 02:24:45.590 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 02:24:45.589 READ NATIVE MAX ADDRESS EXT

Error 1285 occurred at disk power-on lifetime: 4800 hours (200 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f2 7a 59 e5 Error: UNC at LBA = 0x05597af2 = 89750258

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 eb 7a 59 e5 00 02:24:37.207 READ DMA
27 00 00 00 00 00 e0 00 02:24:37.206 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 02:24:45.590 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 02:24:45.590 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 02:24:45.589 READ NATIVE MAX ADDRESS EXT

Error 1284 occurred at disk power-on lifetime: 4800 hours (200 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f2 7a 59 e5 Error: UNC at LBA = 0x05597af2 = 89750258

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 eb 7a 59 e5 00 02:24:37.207 READ DMA
27 00 00 00 00 00 e0 00 02:24:37.206 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 02:24:37.206 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 02:24:37.206 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 02:24:37.206 READ NATIVE MAX ADDRESS EXT

SMART Self-test log structure revision number 1

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.